Installing A Bath tub
Installing A Bath tub
Blog Article
Nearly everybody will have their personal assumption with regards to How to Install a Bathtub Yourself.

Mounting a tub isn't exactly brain surgery, however it does call for solid plumbing, carpentry, as well as sometimes, tiling abilities. Replacing an old tub with a brand-new one is also a moderately hard job. If the old bathtub is easily obtainable, the project can relocate quickly; if you have to open up a wall to eliminate the old bathtub and position the brand-new tub, the job is much harder. In either situation, the project is within a house handyman's abilities, although you will need an assistant to move out the old tub and also set in the brand-new one. Make sure you have qualified on your own for the job as well as are comfortable trying it. Rather than employing a specialist to take over a halfway-completed job, it is better to think about using one before you start. Opportunities are you might require a professional plumber to make tube connections.
This write-up will assist you set up a brand-new bath tub in your washroom if you have actually already purchased a brand-new bathtub as well as do not need to change the plan of your previous water pipes.
Your tools as well as material list need to comprise the following:
Planning for the Installation
Firstly, the supporting framework provided with the bathroom must be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to make sure that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps system to prevent pressure on the tub.
Fit the versatile tap ports to the bottom of both faucets utilizing 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of all of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be suited its last setting.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, then the first thing you must do is detach the supply of water. After doing so, turn on the faucets to drain any water continuing to be in the system. The process of removing the existing faucets can be rather problematic as a result of the limited access that is often the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the faucets. Have a cloth prepared for the remaining water that will certainly come from the pipes. As soon as the supply pipes have actually been eliminated, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this procedure. When the faucets have been removed, the holes in the bath/basin will have to be cleaned of any type of old sealing substance.
Before carrying on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Installing the Tub
Making use of the two wooden boards under its feet, position the tub in the called for position. The wood boards are helpful in equally spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto four little points.
The following objective is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level and also adjusting the feet on the bath tub up until the spirit level checks out level.
To install faucets, fit the bottom of the outermost flexible faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water supply and also examine all joints and also new pipework for leaks as well as tighten them if needed. Load the bath tub as well as additionally inspect the overflow outlet as well as the normal electrical outlet for leakages.
Lastly, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling as well as sealing around the tub should wait up until the bath tub has been used a minimum of when as this will certainly settle it into its last setting.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin making certain that the washing machines are in area between the faucet as well as the sink. Protect the tap in position with the producer provided backnut. When the faucet is safely in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former kind needs to be connected to the faucet finishes first, tightening just by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bath satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to split an inflexible seal, creating the water to penetrate the wall between the bath as well as the tiling, leading to problems with dampness as well as possible leaks to the ceiling below.
You can select from a variety of coloured sealants to assimilate your components and also installations. They are marketed in tubes and also cartridges, and also can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill the bathtub with water prior to securing, to enable the activity experienced when the bathtub is in use. The sealer can split fairly very early if you do not think about this motion prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly available on the marketplace. It is recommended to fit the ceramic tiles making use of water-resistant or water resistant sticky and also cement.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.

As a devoted reader about How to Install a Bathtub, I figured sharing that piece of content was beneficial. Liked our article? Please share it. Let another person locate it. Thank you for your time. Visit us again soon.
Additional Resources
Report this page